BSDWY - LA ARCH L/S P BSE, FL2-250
- MSDS: BSDWY
- Manufacturer: LASTING PAINT INC
- Product Name: LA ARCH L/S P BSE, FL2-250
- National Stock Number: 8010-00N040234
Product Identification
Product ID:LA ARCH L/S P BSE, FL2-250
MSDS Date:09/17/1991
FSC:8010
NIIN:00N040234
MSDS Number: BSDWY
Responsible Party
BALTIMORE, MD 21223
US
Emergency Phone: 301-947-6306
Info Phone: 301-947-6300
Cage: 1055X
Contractor
Telephone: 301-947-6300
Cage: 35178
Ingredients
NON HAZARDOUS INGREDIENTS.
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHAL: MAY CAUSE HEADACHE AND NAUSEA.
SKIN: POSSIBLE PRIMARY IRRITATION (MATERIAL IS SLIGHTLY ALKALINE).
EYES: PRIMARY IRRITATION.
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE KNOWN.
First Aid
First Aid:INHAL: REMOVE TO FRESH AIR. SPLASH(SKIN): REMOVE WITH SOAP &
WATER. REMOVE CONTAMD CLTHG. EYES: FLUSH IMMEDIATELY WITH LARGE
AMOUNT OF WATER FOR AT LEAST 15 MINUTES. CONSULT MD. INGEST: DRINK
1-2 GLAS SES OF WATER TO DILUTE. DO NOT INDUCE VOMITING. CONSULT
MD/POISON CONTROL CENTER IMMEDIATELY. TREAT SYMPTOMATICALLY.
Fire Fighting
Extinguishing Media:USE MEDIA SUITABLE FOR SURROUNDING FIRE.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA & FULL
PROTECTIVE EQUIPMENT.
Unusual Fire/Explosion Hazard:MAY SPLATTER IF HEATED ABOVE 212F. CLOSED
CONTAINERS MAY EXPLODE WHEN EXPOSED TO EXTREME HEAT.
Accidental Release
Spill Release Procedures:SCOOP OR MOP UP SPILLS. ABSORB WITH SAND,
VERMICULITE ETC. TRANSFER TO CONTAINERS FOR DISGARDING. WEAR PROPER
PROTECTIVE GEAR.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:KEEP MATERIAL FROM FREEZING. KEEP
CLOSURE TIGHT AND CNTNR UPRIGHT TO PREVENT LEAKAGE. DO NOT STORE
ABOVE 100F.
Other Precautions:DO NOT TAKE INTERNALLY. AVOID PROLONG OR REPEATED
CONTACT WITH SKIN. DO NOT GET INTO EYES. USE ADEQUATE VENTILATION.
Exposure Controls
Respiratory Protection:NIOSH/MSHA APPROVED MECHANICAL FILTER RESPIRATOR
TO REMOVE SOLID AIRBORNE PARTICLES OF OVERSPRAY DURING SPRAY
APPLICATION.
Ventilation:USE WITH ADEQUATE VENTILATION. PROVIDE EXHAUST SYSTEM WHEN
USED IN ENCLOSED AREAS.
Protective Gloves:RUBBER GLOVES.
Eye Protection:ANSI APRV CHEMICAL WORK GOGGLES
Other Protective Equipment:EYE BATH
Work Hygienic Practices:WASH HANDS BEFORE EATING, SMOKING OR USING WASH
ROOM.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.
Chemical Properties
Boiling Pt:B.P. Text:>212F,>100C
Vapor Density:HVR/AIR
Spec Gravity:1.27
Evaporation Rate & Reference:SLOWER THAN ETHER
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.
Percent Volatiles by Volume:67.21
Stability
Stability Indicator/Materials to Avoid:YES
NONE REASONABLY FORESEEABLE.
Stability Condition to Avoid:NONE KNOWN.
Hazardous Decomposition Products:BURNING OF DRIED COATING CAN PRODUCE
CARBON DIOXIDE & CARBON MONOXIDE.
Disposal
Waste Disposal Methods:DISPOSE OF IN CLOSED CONTAINERS. DO NOT
INCINERATE. BURY IN LANDFILL WHERE PERMITTED. DISPOSAL SHOULD BE
DONE IN ACCORDANCE WITH FEDERAL, STATE & LOCAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.